RP Series
 
Programmable voltage/frequency converter. 800VA-2000VA. Single & three phase output.

The RP Series consists of four models, 801RP, 1251RP, 2001RP and 2003RP. These units are ideal sources for general purpose AC power applications that require variable voltage and frequency at power levels up to 2000 VA. The 2003RP provides three phase output, all other models provide single phase output. With simple knobs used to set voltage, frequency and current limit, the RP Series provides an inexpensive source of AC power in a small and lightweight package. All RP Series power source models can be used in table-top mode or rack-mounted.

Compact ix Series
 
Programmable AC/DC voltage sources. 750VA-2250VA Output. Single & three phase output.

Combination AC and DC Power Source and Power Analyser
Replace multiple instruments with a single multifunction unit

Arbitrary Waveform Generation
User defined voltage waveform and distortion programming
 
Built-in Digital Power Analyser
Analyse frequency and time domain of both voltage and current
 
Scope Capture Capability
Built in voltage and current waveform acquisition capability
 
Powerful Programming Software
Powerful, yet easy to use, instrument control software included (Avionics test software also available)
 
Constant Power Mode
Provides increased current at reduced voltage to maximize efficiency

ix Series II
 
Programmable AC/DC voltage sources. 3000VA to 15000VA output. Single and three phase output.

Combination AC and DC Power
 
Source & Power Analyser
Replaces multiple instruments with one multifunction unit
 
Capable of handling a wide range of loads with 0 to 1 power factor
 
Arbitrary Waveform Generation
Test products for harmonics immunity
 
Built-in Digital Power Analyser
Analyse frequency and time domain of both voltage and current on all phases
 
Scope Capture Capability
Built in voltage and current waveform acquisition capability (iX Series II)
EN61000-3-2 and EN61000-3-3
 
Meets source requirements for IEC Harmonics and Flicker testing
 
Constant Power Mode

MX Series
 
Programmable AC/DC power systems. 15000VA to 180000VA. Single & three phase output configurations.

Extensive output transient generation
 
Voltage, Current and Power measurements
 
Harmonic analysis of Voltage and Current
 
Waveform acquisition of Voltage and Current
 
Programmable output impedance
 
Full output power with 0 to 1 power factor
 
Drive high inrush current input stages
 
High peak current capability
 
Convenient floor standing chassis
 
SCPI programming language support and free application software
 
Optional MIL-STD704 (rev D and E), RTCA/DO-160D, IEC 61000-4-11p and IEC 61000-4-13 tests

FCS Series
 
Programmable AC power systems. 18000VA-54000VA. Single & three phase output configurations.
 
Front Panel Configurable for Single or Multi-Phase Operation
 
Voltage and Frequency Programmable Over IEEE-488 Bus
 
Full Power Line Disturbance Simulation Available
 
Drives Non-Linear Loads and High Peak In-Rush Current Input Stages

LS/LX Series
 
Programmable AC voltage sources. 3000VA to 18000VA output. Single & three phase output configurations.
 
Backward Compatible with L Series AC Sources

Read back Measurements

Powerful output transient generation

Powerful Programming Software
Powerful, yet easy to use, instrument control software included (Avionics test software also available)

TL Series
 
Programmable, linear AC voltage source with high frequency output. 250VA-350VA. Single phase output.
 
45 Hz to 8000 Hz
Fully Programmable
Standard Current measurement
Optional measurements for Peak Current, Voltage, Real Power,
Apparent Power, Power Factor and Crest Factor
Rear panel Connections. (Front panel connections optional.)
Optional IEEE-488 and RS232C interfaces 

L Series
 
Programmable AC voltage sources. 2000VA-18000VA output. Single & three phase output configurations.
 
Mode option allows switching between single and three phase output
Output frequency range up to 5000 Hz.
Full output VA with 0 to 1 power factor
High peak current capability with up to 9:1 crest factor
Efficiency 75% typical or better. Generates less heat and consumes less power
Abbreviated Plain English (APE) programming language support and free Windows ™ application software
Optional MIL-STD704 and RTCA-DO160C test firmware

AC Loads
 

CI 3091LD
 
Programmable electronic AC Loads. Single or multi-phase applications.
 
Programmable electronic AC Loads. Single or multi-phase applications.
 
Programmable Crest Factor and Power Factor
 
Test AC power products for real-world conditions
 
Built-in Read back Measurements
 
Eliminates the need for additional test equipment in bench or ATE applications
 
Remote Control, IEEE-488 and RS232C Interface for automated test applications

Argantix DC Power
 

XDS Series
 
Programmable DC power supplies. 5000W to 90000W output.
 
The XDS Series offers all the basic DC power supply capabilities needed for a wide range of applications and provides cost effective alternative to larger and more expensive products typically used for these applications

KDC Series
 
Programmable DC power supplies. Advanced control features. 5000W to 90000W output.
 
The KDC Series packs up to 15 kW of DC power in a 5.25" (3U) chassis. Despite the high power density of the design, the KDC Series provides a low noise, stable output. The DC voltage ranges are 30 V to 600 Vdc, which supports a wide range of applications.
 
The KDC Series comes with an RS-232 as the standard remote programming interface. The IEEE-488/GPIB & isolated analogue interface are optional. The KDC Series continuously measures output voltage, current, peak current, and power.

Current Sources
 

FX Series
 
Programmable voltage/current sources. Designed specifically for watt hour meter applications.
 
With the combined voltage and current source in a single compact chassis, the FX Series is the ideal choice for the simulation of high power levels. Either single or multi-phase, this versatile source can simulate power levels from just a few milliwattsn to 54kW single phase or 162 kW three-phase and provides a universal system for both manual and programmable control applications.

CS Series
 
Programmable AC current sources. 3000VA-18000VA. Single & three phase output.
 
The CS Series represents an advanced AC current source that addresses increasing demands on manufacturers to test products using real-world current profiles. By combining true current transconductance amplifiers with an advanced digital controller and harmonic power analyser, CS Series current sources are capable of performing tests that would traditionally have been difficult to accomplish.

Compliance Test Systems
 

CTS Series
 
Conducted emissions compliance test systems. Performs the IEC harmonics and flicker tests.
 
Available in a range of power levels from 3000 VA to 90000 VA, the CTS series provides cost effective full compliance testing for both single and three phase products. The CTS series is the only compliance test system on the market that uses a PC bus based high speed data acquisition system to record complete data on all measurements taken from the Equipment Under Test (EUT). This effectively eliminates the IEEE-488 interface throughput bottle necks that plagues most IEC test systems available today.
 
The powerful CTS test software takes full advantage of this high speed acquisition system by displaying real-time data and continuous pass fail calculations during the entire test run. No need to wait for a two hour flicker test to finish before the outcome of the test is known. With a CTS system, the operator is always up to date on test progress and test results.